Problem mit ISDN Remote Einwahl

[Klettermaxx 10]

Servus zusammen,

 

ich habe seit etlicher Zeit keine ISDN Remote Einwahl mehr konfiguriert und kann mich mit der folgenden Config nicht einwählen. Ggf. hat einer von Euch eine Idee.

 

 

 

interface BRI0

no ip address

encapsulation ppp

isdn switch-type basic-net3

isdn point-to-point-setup

isdn caller xxx

isdn answer1 xxx

isdn calling-number xxx

 

interface Dialer2

description "ISDN-Remoteeinwahl"

ip address 192.168.10.1 255.255.255.0

ip nat inside

ip virtual-reassembly

encapsulation ppp

dialer pool 2

dialer remote-name xxx

dialer idle-timeout 180

dialer-group 1

peer default ip address dhcp-pool ISDN-Remoteeinwahl

no cdp enable

ppp authentication chap callin

ppp multilink

 

dialer-list 1 protocol ip permit

[Klettermaxx 10]

So und hier der Debug.

 

 

 

Nov 10 2007 03:48:21.491 CET: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 78 changed to down

Nov 10 2007 03:48:21.499 CET: ISDN BR0 Q931: Ux_DLRelInd: DL_REL_IND received from L2

Nov 10 2007 03:48:41.674 CET: ISDN BR0 Q931: RX <- SETUP pd = 8 callref = 0x39

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x89

Calling Party Number i = 0x2181, 'xxx'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, 'xxx'

Plan:ISDN, Type:Subscriber(local)

Nov 10 2007 03:48:41.682 CET: ISDN BR0 EVENT: process_rxstate: ces/callid 1/0xEA calltype 1 HOST_INCOMING_CALL

Nov 10 2007 03:48:41.682 CET: ISDN BR0 EVENT: host_incoming_call: call_id 0x00EA, Guid = 0000023D81CB bchan 0

Nov 10 2007 03:48:41.690 CET: ISDN BR0 **ERROR**: host_incoming_call: Rejecting call. isdn screening failed

Nov 10 2007 03:48:41.694 CET: ISDN BR0 EVENT: process_rxstate: ces/callid 1/0xEA calltype 1 HOST_DISCONNECT_ACK

Nov 10 2007 03:48:41.706 CET: ISDN BR0 Q931: RX <- SETUP pd = 8 callref = 0x26

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x8A

Calling Party Number i = 0x2181, 'xxx'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, 'xxx'

Plan:ISDN, Type:Subscriber(local)

Nov 10 2007 03:48:41.718 CET: ISDN BR0 EVENT: process_rxstate: ces/callid 1/0xEB calltype 1 HOST_INCOMING_CALL

Nov 10 2007 03:48:41.718 CET: ISDN BR0 EVENT: host_incoming_call: call_id 0x00EB, Guid = 0000023D81CB bchan 1

Nov 10 2007 03:48:41.726 CET: ISDN BR0 **ERROR**: host_incoming_call: Rejecting call. isdn screening failed

Nov 10 2007 03:48:41.730 CET: ISDN BR0 EVENT: process_rxstate: ces/callid 1/0xEB calltype 1 HOST_DISCONNECT_ACK

Nov 10 2007 03:48:42.726 CET: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 78 changed to up

Nov 10 2007 03:48:42.730 CET: ISDN BR0 **ERROR**: L3_Go: Multi nlcb DL_EST, cid 0xEB cr 0xA6 ev 0x300 ces 1

Nov 10 2007 03:48:42.734 CET: ISDN BR0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB9

Cause i = 0x8095 - Call rejected

Nov 10 2007 03:48:42.762 CET: ISDN BR0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xA6

Cause i = 0x8095 - Call rejected

[blackbox 10]

Hallo,

 

warum isdn point-to-point-setup ? Du hast doch keine TEI fix definiert ? Ansonsten hört sich das so an, als wenn die Rufnummern nicht zusammen passen.

[rob_67 10]

hi,

 

die eingehende rufnummer wird rejected,

 

 

--> mit isdn caller auf dem bri ohne führende nullen eintragen...

 

 

gruss

 

 

rob